High-Side

Here is a practical example of implementing a High-Side circuit with a RevPi DIO | DO module.

Useful information for this article:
https://revolutionpi.com/tutorials/overview-revpi-i-o-modules/konfiguration-dio-di-do/

Features

A high-side switch refers only to the position of the switch. A high-side switch switches the positive supply voltage. See the illustration below.

All 14 output ports can supply 500mA simultaneously, in high-side mode.
All outputs can be individually set to push-pull, which is the default setting, or to high-side mode.

If the module gets too warm, all ports are switched off. This prevents the device from being damaged.
See under the tuple “Status” under the following link https://revolutionpi.com/tutorials/overview-revpi-i-o-modules/konfiguration-dio-di-do/

Wiring

Connect The Revolution Pi DIO as in the Following picture

1. Connect 12V -24V to the X4 plug located on the bottom of the device.

2. Connect 12V -24V to the X2 plug on the top of the unit to supply power to the output ports.

3. Connect 12V -24V to the X2 plug on the top of the unit to supply power to the Input ports.

4. Connect all the grounds marked on the plugs X4 and X2 together.

5. Connect one port from Output 1 to 14 to the electrical consumer [M], [M] can be a 24V LED

6. Connect the ground from the electrical consumer [M] to the same ground as the Revolution Pi (X4 plug)

Connect the extension module with a base module

Connect the Revolution Pi DIO to the Revolution Pi, with a PiBridge.

RevolutionPi IO-Modules FAQ |

PiCtory Configuration

The following describes how to set up the PiCtory configuration to run the DIO in high-side mode.

For this example, you can use a Revolution Pi Core or Connect. The only difference for this example is which base module is inserted into PiCtory.

Set output to high-Side mode

for high-side mode, 2 bytes are available to switch each output from push-pull to high-side.
Set the corresponding bit to 1 for high-side mode and 0 for push-pull mode. The default value is 0x0000.

For example, you want to run Output O_14, O_10 and O_2 in high-side mode.
The Binary value is 0010100000000010₂ = 10.242₁₀

10.242 is the decimal value you need to enter into the corresponding field.

Save the config like in the picture below, with “Save as Start-Config”. This Configuration will be loaded at each boot.

Switching output with piTest from PiControl

Check that the Revolution Pi DIO is detected correctly.

piTest -d

Found 2 devices:

Address: 0 module type: 105 (0x69) RevPi Connect V1.0
Module is present
     input offset: 113 length: 6
    output offset: 119 length: 5

Address: 31 module type: 96 (0x60) RevPi DIO V1.4
Module is present
     input offset: 0 length: 70
    output offset: 70 length: 18

Control of the DIO Output ports

Switch Output 1 (0_1)

piTest -1 -r O_1
Bit value: 0

piTest -w O_1,1
Set bit 0 on byte at offset 70. Value 1

piTest -1 -r O_1
Bit value: 1

If output 1 = 1, the circuit is closed.

If output 1 = 0, then the circuit is not closed.

Push-Pull

Here is a practical example of implementing a push-pull circuit with a RevPi DIO | DO module.

Useful information for this article:
https://revolutionpi.com/tutorials/overview-revpi-i-o-modules/konfiguration-dio-di-do/

Wiring

Here, there are two possibilities for a circuit:

PiCtory Configuration

The register “OutputPushPull” contains a bit field in which is defined which function is active:

• 0 := Push-Pull

• 1 := High-Side

For example, the following configuration should be created:

11 1111 1111 1110 dual = 16382 decimal

• Write the decimal value into the variable “OutputPushPull”

• Save the PiCtory configuration

• Restart cyclic data communication

Switch

piTest -w O_1,1 # Output 1 := 24V
piTest -w O_1,0 # Output 1 :=  0

Read input values

How to read values from the inputs of the RevPi DIO | DI

piTest -r I_1 # Input 1 := 12V
1

piTest -r I_1 # Input 1 :=  0V
0

Input Mode

If you would like to know more about the input modes, please watch our video.

https://revolutionpi.com/tutorials/video-tutorials#VT14 | Tutorial 14 – Counter and Encoder

Encoder

if you want to use an encoder an any input port of the RevPi DIO | DI. then set the variable

InputMode_x_yz to Encoder

Counter

All inputs, of the DIO, DI that have been activated, can count individually on rising or falling edge.

To read the value of on counting register:

piTest -r Counter_1_xyz

If there are incorrect inputs, you should switch on the debouncing. By default, this is switched off.
Set it to 25us, 750us or 3ms.

PWM

To activate the PWM signal, you have to set the following variable to 1.

OutputPWMActive_i04 = 1

In the PiCtory you can configure the period of the PWM Signal

This function is available on the RevPi DIO | DO

each individual output can send out a PWM signal.

Note: If you would like to know more about the input modes, please watch our video.

https://revolutionpi.com/tutorials/video-tutorials#VT14 | Tutorial 15 – PWM on RevPi DIO

Troubleshooting

PiCtory Checklist

Revolution Pi Checklist

https://revolutionpi.com/tutorials/images/firmware-update

Further Information

https://kunbus-gmbh.atlassian.net/wiki/spaces/KS/pages/2629566465/RevolutionPi+IO-Modules+FAQ?parentProduct=JSM-Portal&parentProductContentContainerId=10001&initialAllowedFeatures=disable-login-flow.disable-share&locale=en-US#How-to-wire-the-RevolutionPi-AIO%2C-MIO%2C-DIO%2C-DI%2C-DO-modules%3F

https://kunbus-gmbh.atlassian.net/wiki/spaces/KS/pages/2629566465/RevolutionPi+IO-Modules+FAQ?parentProduct=JSM-Portal&parentProductContentContainerId=10001&initialAllowedFeatures=disable-login-flow.disable-share&locale=en-US#How-much-RevPi-IO-Modules-can-I-connect-to-a-RevPi

https://revolutionpi.com/io-modules?noredirect=en-US