Versions Compared

Old Version 47

changes.mady.by.user Markus Vogt

Saved on

compared with

New Version 48

changes.mady.by.user Markus Vogt

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

We are happy that you have chosen our product and you found your way to this quick start.

This quick tart describes how to setup your DF PROFINET IO board (Controller and Device) with the LabVIEW Driver and run the example code.

Table of Contents

Content

The product

Basics

Instructions

Help

The product

For further information check out the DF PROFNET IO product site:

https://www.kunbus.com/pc-cards-profinet-io.html

Hardware:

  • DF PROFINET IO (PCI/CPCI/PCIe)

Software package:

  • LabVIEW™ PROFINET VISA driver for Windows 7 / Windows 10 and LabVIEW™ RT

  • Configurator 3 for PROFNIET diagnosis and configuration

  • Network Configurator for diagnosis and configuration

The PROFINET Controller and Device are located as shown below.

The status LED bar shows red after booting and after a couple of seconds green for “standby - DF PROFINET IO board is ready to use” on the Controller port.

Info

Keep in mind this is a quick start! Refer to the user documentation for a more detailed description.

(LabVIEW: menu/ #tbd

#tbd Screenshot von labview/help

Basics

  • the LabVIEW Driver does support Windows 7 / 10 - 64/32 Bit + LabVIEW 2014 32 Bit and higher

  • refer to the section Help if you got some issues by following the instructions below

  • refer to the DF PROFINET IO | FAQ if you need any further help

  • make sure you installed the National Instruments NI VISA driver package

Instructions

Expand
titleSetting up the System

Action

Shut down your system and mount the board in your PC

boot your PC

Install the LabVIEW PROFINET VISA driver package

  1. the file is located on a DVD or USB stick in the boards shipping box

  2. Chose the setup bit version regarding your Windows OS

Expand
titleSetting up your first PROFINET Network

Setting up your first PROFINET network by using the Boards controller and device

Action

Additional Information

Connect the two Ethernet ports (PROFINET - controller and device) on the board with a Ethernet cable directly

Configure the board as shown in the video:

#tbd new video

board_conf.mp4

Close the Configurator 3 (it is only for configuration and diagnosis)

Run the LabVIEW GettingStarted example code as shown in the video

The boards controller and device are exchanging data via PROFINET

#tbd convert to .mp4 (playable in FF)

vid2.mkv

Help

find below some typical things you can check and do if you got any issue during setting up the DF PROFINET IO board.

Expand
titleSetup

Action

Additional information

Keep your Windows and LabVIEW updated

Make sure the NI VISA driver package is installed

Visible in NI MAX #tbd new screenshot

Check if the board is recognized on your PC in the device manager

Make sure to allow remote control for your NI VISA driver by adding “*” as permission

#tbd neuer screenshot

Expand
titleUsing the PROFINET Controller or Device GettingStarted Code example

Action

Additional information

You can not run Configurator 3 and DF PROFINET IO LabVIEW VIs at the same time.

  1. Close the Configurator 3 for using the controller or device.

  2. It is for configuration and diagnosis

be aware to use the correct Ethernet port for the controller or the device

APDU status 0x21 is shown on your controller: #tbd scs

  1. you have either the device not running or the wrong PROFINET device name used in your configuration

Info

For further help, please check out the DF PROFINET IO | FAQ

Releated Articels

Filter by label (Content by label)
showLabelsfalse
max5
spacescom.atlassian.confluence.content.render.xhtml.model.resource.identifiers.SpaceResourceIdentifier@968
showSpacefalse
sortmodified
typepage
reversetrue
labelskb-how-to-article
cqllabel = "kb-how-to-article" and type = "page" and space = "KS"
Page Properties
hiddentrue

Verwandte Vorgänge

Jira Legacy
serverId6a616e0c-dd66-30e3-95b5-0fa763638e21
keySUP-414