Versions Compared

Old Version 51

changes.mady.by.user Markus Vogt

Saved on

compared with

New Version 52

changes.mady.by.user Markus Vogt

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

We are happy that you have chosen our product and you found your way to this quick start.

This quick tart describes how to setup your DF PROFINET IO board (Controller and Device) with the LabVIEW Driver and run the example code.

Content

The product

Basics

Instructions

Help

The product

Expand
titleDF PROFINET IO - details

For further information check out the DF PROFNET IO product site:

https://www.kunbus.com/pc-cards-profinet-io.html

Hardware:

  • DF PROFINET IO (PCI/CPCI/PCIe)

Software package:

  • LabVIEW™ PROFINET VISA driver for Windows 7 / Windows 10 and LabVIEW™ RT

  • Configurator 3 for PROFNIET diagnosis and configuration

  • Network Configurator for diagnosis and configuration

The PROFINET Controller and Device are located as shown:

The STATUS LED bar shows red after booting and after a couple of seconds green for “standby - DF PROFINET IO board is ready to use” on the Controller port.

Info

Keep in mind this is a quick start! Refer to the user documentation for a more detailed description.

(LabVIEW: menu/ #tbd

Basics

  • the LabVIEW Driver does support Windows 7 / 10 - 64/32 Bit + LabVIEW 2014 32 Bit and higher

    • refer

    Expand
    titlesome basics before you start:

    • Refer to the section Help if you got some issues by following the instructions below

    refer
    make

    • Make sure you installed the National Instruments NI VISA driver package

    • The LabVIEW PROFINET VISA driver does support Windows 7 / 10 - 64/32 Bit + LabVIEW 2014 32 Bit and higher

    Instructions

    Expand
    titleSetting up the System

    Action

    Shut down your system and mount the board in your PC

    boot your PC

    Install the LabVIEW PROFINET VISA driver package

    1. the file is located on a DVD or USB stick in the boards shipping box

    2. Chose the setup bit version regarding your Windows OS

    Expand
    titleSetting up your first PROFINET Network

    Setting up your first PROFINET network by using the Boards boards controller and device

    Action

    Additional Information

    Connect the two Ethernet ports (PROFINET - controller and device) on the board with a Ethernet cable directly

    Configure the board as shown in the video:

    #tbd new video

    		board_conf.mp4

    Close the Configurator 3 (it is only for configuration and diagnosis)

    Run the LabVIEW GettingStarted example code as shown in the video

    The boards controller and device are exchanging data via PROFINET

    #tbd convert to .mp4 (playable in FF)

    		vid2.mkv

    Help

    find below some typical things you can check and do if you got any issue during setting up the DF PROFINET IO board.

    Expand
    titleSetup

    Action

    Additional information

    Keep your Windows and LabVIEW updated

    Make sure the NI VISA driver package is installed

    Visible in NI MAX #tbd new screenshot

    Check if the board is recognized on your PC in the device manager

    Make sure to allow remote control for your NI VISA driver by adding “*” as permission

    #tbd neuer screenshot

    Expand
    titleUsing the PROFINET Controller or Device GettingStarted Code example

    Action

    Additional information

    You can not run Configurator 3 and DF PROFINET IO LabVIEW VIs at the same time.

    1. Close the Configurator 3 for using the controller or device.

    2. It is for configuration and diagnosis

    be aware to use the correct Ethernet port for the controller or the device

    APDU status 0x21 is shown on your controller: #tbd scs

    1. you have either the device not running or the wrong PROFINET device name used in your configuration

    Info

    For further help, please check out the DF PROFINET IO | FAQ

    Releated Articels

    Filter by label (Content by label)
    showLabelsfalse
    max5
    spacescom.atlassian.confluence.content.render.xhtml.model.resource.identifiers.SpaceResourceIdentifier@968
    showSpacefalse
    sortmodified
    typepage
    reversetrue
    labelskb-how-to-article
    cqllabel = "kb-how-to-article" and type = "page" and space = "KS"
    Page Properties
    hiddentrue

    Verwandte Vorgänge

    Jira Legacy
    serverId6a616e0c-dd66-30e3-95b5-0fa763638e21
    keySUP-414